#Launch x431 pro 3s how to#
#Launch x431 pro 3s registration#
#Launch x431 pro 3s android#
#Launch x431 pro 3s code#

It also supports quick diagnosis via one-button VIN scanning. This diagnostic tablet supports ECU coding function on a large amount of makes, including Benz, Ford and more. ThatвЂ™s really time-saving.ДЇeatures dustproof, drop resistant, greaseproof and waterproof (the screen), you will not be bothered by the grease, dust and water when diagnosing and fixing the vehicle.

#Launch x431 pro 3s android#

The Android 7.1 system also facilitates a super good experience of diagnosis.ДЄccompanied with 7000mAh battery, you are able to continuously use the tool about 4 вЂ“ 6 hours, depending on what operation you do, before recharging it. Therefore, you can find the malfunctioned parts directly and solve problems quickly. You are able to diagnose car freely, either at your workbench or under the hood.Д®quipped with a large 10.1вЂі display, different data in wavelike form can be displayed at the same time. Instead of diagnosing car via a diagnostic cable, this auto scanner provides you with much convenience due to its Bluetooth feature. In the following post, I will introduce more info about this new black X431 V+ WhatвЂ™ more, new black x431 v+ has 2G RAM and expandable body memory up to 128 GB. In the above table, you could find that this new black x431 V+ owns higher Android system with 1.4 GHz Quad-cone processor. In this post, I will compare the two X431 V+ Pro3 tools first and more info the new one.Д¬omparison about old red X431 V+ and new black X431 V+: What is the difference between then and what new spotlights does the new black X431 have.

#Launch x431 pro 3s how to#

This is how to use Launch X431 Diagnostic Tool to do an immobilizer key register for Nissan after replacing BCM.You may notice that Launch has published a new black x431 v+ pro3. Once done, all keys can start the engine. Check that security indicator blinks at intervals of approximately 3s.

#Launch x431 pro 3s registration#

Registration unsuccessful if buzzer does not sound or sounds 3 times For models with remote control engine starter, buzzer of remote control engine starter sounds once.Insert ignition key into key cylinder and turn it to ON.Therefore, it is necessary to end operation. A maximum of 5 ignition keys can be registered by repeating procedure from step2 to step4 using unregistered ignition keys.ДЄfter key registration operation, they system returns to key registration mode.Turn ignition switch to OFF, remove ignition key, wait for 3s or more.Check that security indicator blinks 5 times.Insert unregistered ignition key into ignition key cylinder, turn it ON, wait for 5s or more.Remove inserted ignition key from ignition key cylinder.The system will automatically proceed to initialization ECU after operation.

Insert ignition key into ignition key cylinder and turn it ON. Input immobilizer code(4 digits PIN) for initialization.

The immobilizer codes (PIN) were read out, press вЂњOKвЂќ. Therefore, all of the customerвЂ™s keys should be obtained before starting this procedure. This procedure erase all registered key Ids. NATS(Nissan Anti-theft System) > After replacing or installing operation > Replace BCM Local diagnose > Nissan > OK > Manually select > Far east > Malaysia > Almera > N17 > 11/2014 > Health report Using Launch X431 V, X431 V+ or X431 Pro Mini can do an immobilizer NATS(Nissan Anti-theft System) key register for Nissan.ДЇollowing weвЂ™re taking a 2014 Nissan Almera N17 to make a demo on how to do.Д¬onnect X431 scan tool into OBD, go to scan systems firstly,

#Launch x431 pro 3s code#

This code usually comes out when a not registered or damaged key is used to start the engine.

After replacing BCM, Nissan may have a fault code P1614.